spec no: dsai6160 rev no: v.5a date: apr/12/2016 page: 1 of 5 approved: wynec checked: allen liu drawn: m.liu er p: 1102013103 3mm right angle led indicator part number: wp934ad/id high efficiency red features z ideal for card edge status indication. z pre-trimmed leads for pc board mounting. z black case enhances contrast ratio. z wide viewing angle. z high reliability - life measured in years. z housing ul rating:94v-0. z housing material: type 66 nylon. z rohs compliant. description the high efficiency red source color devices are made with gallium arsenide phosphide on gallium phosphide orange light emitting diode. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25(0.01") unless otherwise noted. 3. lead spacing is measured where the leads emerge from the package. 4. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice .
spec no: dsai6160 rev no: v.5a date: apr/12/2016 page: 2 of 5 approved: wynec checked: allen liu drawn: m.liu er p: 1102013103 selection guide absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c part no. emitting color (material) lens type iv (mcd) [2] @ 10ma v iewing angle [1] min. typ. 2 1/2 high efficiency red (gaa sp/gap) red diffused 12 30 40 *10 *20 wp934ad/id symbol parameter emitting color typ. max. units test conditions peak peak wavelength high efficiency red 627 nm i f =10ma d [1] dominant wavelength high efficiency red 617 nm i f =10ma ? 1/2 spectral line half-width high efficiency red 45 nm i f =10ma c capacitance high efficiency red 15 pf v f =0v;f=1mhz v f [2] forward voltage high efficiency red 1.9 2.5 v i f =10ma i r reverse current high efficiency red 10 ua v r = 5v parameter values units power dissipation 75 mw dc forward current 30 ma peak forward current [1] 160 ma reverse voltage 5 v operating/storage temperature -40c to +85c lead solder temperature [2] 260c for 3 seconds lead solder temperature [3] 260c for 5 seconds notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity / luminous flux: +/-15%. * luminous intensity value is traceable to cie127-2007 standards. notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to cie127-2007 standards. 4. excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradat ion or premature failure. notes: 1. 1/10 duty cycle, 0.1ms pulse width. 2. 2mm below package base. 3. 5mm below package base. 4. relative humidity levels maintained between 40% and 60% in pr oduction area are recommended to avoid the build-up of static electricity ? ref jedec/jesd625-a and jedec/j-std-033.
spec no: dsai6160 rev no: v.5a date: apr/12/2016 page: 3 of 5 approved: wynec checked: allen liu drawn: m.liu er p: 1102013103 high efficiency red wp934ad/id
spec no: dsai6160 rev no: v.5a date: apr/12/2016 page: 4 of 5 approved: wynec checked: allen liu drawn: m.liu er p: 1102013103 packing & label specifications wp934ad/id terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
spec no: dsai6160 rev no: v.5a date: apr/12/2016 page: 5 of 5 approved: wynec checked: allen liu drawn: m.liu er p: 1102013103
|
